Module Kits DIY Kit HX1838
Latest infrared wireless remote control kit consists Mini Slim 38KHz IR remote control and infrared receiver modules, Mini Slim infrared remote control with 17 function keys, firing distances of up to 8 meters, ideal for a variety of devices in the control room. IR receiver module can receive standard 38KHz modulation remote control signal, through programming, you can achieve remote control signal decoding operation, which can produce a variety of remote control robots and interactive works.
Ultra-thin infrared remote control product parameters:
1 Transmission Distance: 8m above (specific and surroundings, the receiver sensitivity and other factors)
2 Effective angle: 60 degrees
3 Sticking Material: 0.125mmPET, the effective life of 20,000 times.
4. Stable quality, cost-effective
5 quiescent current 3-5uA, dynamic current 3-5mA.
ULN2003 28BYJ-48
Features:
Gear Stepper Motor DC 5V 4 Phase Step Motor Reduction Step Motor
Brand new and high quality.
Diameter: 27mm.
Voltage: 5V.
Step angle: 5.625 x 1/64.
Reduction ratio: 1/64.
5 lines cable 4 phase stepper motor can be driven by ULN2003 chip.
It also can be connected as 2 phase to use.
Specification:
Original box: No
Color: Silver
Item size: 31*27*19mm
Net weight: 35g
Package weight: 44g
UNO R3 KIT
CNC Shield Expansion Board
- Arduino UNO R3 Board, MCU: ATmega328, USB interface: ATmega16U2.
- PWM Spindle and direction pins. 4-Axis support. Runs on 12-36V DC.
- 2 x End stops for each axis (6 in total).
- 4Pcs A4988 Stepper Motor Driver with radiator.
- CNC Shield Board:
Latest Arduino CNC Shield Version 3.0
GRBL 0.9 compatible
4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13)
2 x End stops for each axis (6 in total)
Coolant enable
Compatible with A4988 or DRV8825 stepper driver
Runs on 12-36V DCArduino UNO R3 Board:
MCU: ATmega328
USB interface: ATmega16U2
Operating voltage: 5V
Digital I/O pins: 14 (including 6 with PWM capability)
Analog input pins: 6
I-I/O pin output current: 40mA max
3.3V output current: 150mA max
Flash memory: 32 kB (0.5kB used by bootloader — included)
Static RAM (SRAM): 2 kB
EEPROM: 1 kB
Clock speed: 16MHzA4988 Stepper Motor Driver:
A4988 Stepper Motor Driver Board is a breakout board for Allegro’s A4988 DMOS Micro stepping Driver with Translator and Overcurrent Protection;Low RDS (On) Output :
Automatic current decay mode detection / selection
Mix with slow current decay modes
Synchronous rectification for low power dissipation
Internal UVLO
Crossover-current protection
3.3 and 5 V compatible logic supply
Thermal shutdown circuitry
Ground fault protection
Load short-circuit protection
Five selectable step modes: full, 1/2, 1/4, 1/8 and 1/16
Warning: Connecting or disconnecting a stepper motor while the driver is powered can destroy the driver. (More generally, rewiring anything while it is powered is asking for trouble).Package Contents:
1 x CNC Shield Board
1 x UNO R3 Board for Arduino
4 x A4988 Stepper Motor Driver
4 x Heat Sink
RFID Starter Kit for Arduino UNO R3 Upgraded Version Learning Suite Kit
Uno Kit Starter Kit, RFID Learning Suite including:
1pcs UNO R3(100% Original with LOGO)
1pcs USB cable
1pcs 65 jumper wires
1pcs 830 Point BREADBOARD
15pcs led (Red, Green, Yellow)
30pcs resistance(220R, 10K, 1K)
1pcs 10 pin dupont line(male to female)
1pcs potentiometer
1pcs active buzzer
1pcs passive buzzer
1pcs 74HC595N
1pcs Infrared receiving head
1pcs LM35DZ
1pcs Flame sensor
2pcs Roll Ball Switch
3pcs 5mm LDR
5pcs Button Switch with Cap
1pcs IR remote control
1pcs one digital tube
1pcs four digital tube
1pcs 8*8 dot matrix tube
1pcs UNL2003 driver board
1pcs 5V stepper motor
1pcs SG90
1pcs LCD1602 IIC I2C
1pcs PS2 game joystick module
1pcs DHT11 Temperature and Humidity sensor module
1pcs Water level measurement module
1pcs RFID module
1pcs RFID key ring
1pcs RFID card
1pcs sound sensor module
1pcs one road relay module
1pcs RTC module
1pcs 16 buttons matrix keyboard module
1pcs RGB three color module
1pcs 9V Battery Connector
DIY Kit
This is a quite fantastic DIY electronic clock. Based on micro controller, IC board and some electronic components, you can easily assemble and solder it quickly. With digital tube, you can watch time clearly no matter day time or at night. It is suitable for DIY enthusiasts, school training lessons etc. Why not not come and purchase one
Features:
With written program, you can use it directly.
Based on micro controller, precise timekeeping and mini in size.
Easy to set & adjust hour, minute, second ,date, week and hourly chime.
Can be used as thermometer to test and display temperature per 30sec.
Light control, the clock will automatically be brighter during the day than the night.
With transparent case, components can be well protected and the clock looks stylish.
Perfect for electronic DIY enthusiasts, school training lessons etc.
Note
1. It can work when blackout with a 3V lithium battery.(not included)
2. You need to solder it yourself.
3. Since its working voltage is DC 5V, thus can be powered through phone charger with a USB wire.
4. For more specific function and application method, please read our English user manual.
Specifications:
Display 4-digit LED
Power Supply 3V CR1220 Button Battery (not included)
Working Voltage DC 5V
Working Current 40mA
Clock Size 7 2.5 1.2cm 2.76 0.98 0.47in
IC Board Size 7.2 2.7cm 2.84 1.06in
Kit Weight 82g 2.9oz
Package Size 12 8.5 3.5cm 4.72 3.35 1.38in
Package Weight 85.5g 3.01oz
Package List
1 x DIY Electronic Clock Kit(Battery not Included)
1602 LCD 830 Breadboard
Uno Kit Starter Kit, RFID Learning Suite including:
1pcs UNO R3
1pcs USB cable
1pcs 65 jumper wires
1pcs 830 Point BREADBOARD
15pcs led (Red, Green, Yellow)
30pcs resistance(220R, 10K, 1K)
1pcs 10 pin dupont line(male to female)
1pcs potentiometer
1pcs active buzzer
1pcs passive buzzer
1pcs 74HC595N
1pcs Infrared receiving head
1pcs LM35DZ
1pcs Flame sensor
2pcs Roll Ball Switch
3pcs 5mm LDR
5pcs Button Switch with Cap
1pcs IR remote control
1pcs one digital tube
1pcs four digital tube
1pcs 8*8 dot matrix tube
1pcs UNL2003 driver board
1pcs 5V stepper motor
1pcs SG90
1pcs LCD1602 IIC I2C
1pcs PS2 game joystick module
1pcs DHT11 Temperature and Humidity sensor module
1pcs Water level measurement module
1pcs RFID module
1pcs RFID key ring
1pcs RFID card
1pcs sound sensor module
1pcs one road relay module
1pcs RTC module
1pcs 16 buttons matrix keyboard module
1pcs RGB three color module
1pcs 9V Battery Connector
1pcs high quality Retail box
EL-KIT-012 UNO
- Elegoo smart robot car: an educational kits for beginners to get hands-on experience about Arduino programming, electronics assembling and robotics knowledge.
- Over 10 upgrades: such as built-in ir remote sensor on the board, 3 line tracking modules in one board, upgraded battery with protection board and now you can install
- Easy to assemble: all the module interface has Xh2.54 ports, which makes it much easier and very convenient to assemble the car and reduce the errors
- Working modes: line tracking, obstacle avoidance, ir-remote control and Bluetooth control over your phone with our app on iOS and android. Kit based on UNO R3 controller board
- Refined tutorial: HD rendering instructions of how to assemble the robot car from scratch and all the necessary programs and codes are included
Product Description:
Component List:
1pcs UNO R3
1pcs USB cable
1pcs V5.0 extension board V3.0
1pcs L298N motor driver board V3.0
1pcs ultrasonic Sensor
1pcs ultrasonic holder
1pcs servo motor
1pcs servo motor fixed plate
1pcs Bluetooth module
1pcs line tracking module
4pcs motor
1pcs remote
1pcs charger
1pcs cell box
1pcs tape
8pcs separation shims
2pcs acrylic plates
4pcs wheel
8 bags of screws and nuts for sensors and modules
4pcs aluminum blocks
10pcs copper columns
1pcs plastic box
1pcs CD with tutorial
Several DuPont wires
Several fix tools
Elegoo Smart Robot Cat Kit V3.0 is an educational and fun kit based on UNO R3 controller board designed for both beginners and professionals to learn electronics, programming and robotics. With our easy-to-follow tutorialassembling this robot car kit would be very intuitive and simple regardless of whether you are an engineer or a novice.
Building up your own robotic project has never been so easy and fun. Just follow our tutorial and step by step you will have your own running car kit within no time. This kit enables you to have a good quality time with your children and empower them to develop and inspire their imaginations.
If your kids, family or friends are attracted to the electronics and robotics world, this kit would be a great choice and perfect gift for them to start their first step on electronic journey.
37 IN 1 SENSOR KITS FOR ARDUINO HIGH-QUALITY IN PLASTIC BOX Works with Official for Arduino Boards
Material: Circuit board
.Includes basic components and sensors
.Compatible for Arduino
Specifications:
.Package Dimensions: 273*190*43mm
.Weight: 431g
Package Included:
. 1 x Small passive buzzer module
.1 x 2-color LED module
.1 x Hit sensor module
.1 x Vibration switch module
.1 x Photo resistor module
.1 x Key switch module
.1 x Tilt switch module
.1 x 3-color full-color LED SMD modules
.1 x Infrared emission sensor module
.1 x 3-color LED module
.1 x Mercury open optical module
.1 x Yin Yi 2-color LED module 3MM
.1 x Active buzzer module
.1 x Temperature sensor module
.1 x Automatic flashing colorful LED module
.1 x Mini magnetic reed modules
.1 x Hall magnetic sensor module
.1 x Infrared sensor receiver module
.1 x Class Bihor magnetic sensor
.1 x Magic light cup module
.1 x Rotary encoder module
.1 x Optical broken module
.1 x Detect the heartbeat module
.1 x Reed module
.1 x Obstacle avoidance sensor module
.1 x Hunt sensor module
.1 x Microphone sound sensor module
.1 x Laser sensor module
.1 x 5V relay module
.1 x Temperature sensor module
.1 x Temperature sensor module
.1 x Linear magnetic Hall sensors
.1 x Flame sensor module
.1 x Sensitive microphone sensor module
.1 x Temperature and humidity sensor module
.1 x XY-axis joystick module
.1 x Metal touch sensor module
.1 x HIGH QUALITY Box
.1 X learn tutorial CD
PHOTOS :
Mega2560 Board + 3.2" TFT
Product description
Features:
—Mega2560 Board—
The MEGA 2560 is designed for more complex projects. The ATmega2560 on the Mega 2560 comes preprogrammed with a bootloader that allows you to upload new code to it without the use of an external hardware programmer.
It has 54 digital I/O pins (of which 15 can be used as PWM outputs), 16 analog inputs, 4 UARTs (hardware serial ports), a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button.
—3.2» Full Color TFT Touch Screen—
3.2″ TFT LCD Display has 40pins interface and SD card and Flash reader design. It is a powerful and mutilfunctional module for your project.
The touch screen include a controller ILI9325, it’s a support 16bit data interface , easy to drive by many MCU like arduino families, STM32, AVR and 8051. It is designed with a touch controller in it and has a wide viewing angle.
The touch IC is XPT2046 , and touch interface is included in the 40 pins breakout. It is the version of product only with touch screen and touch controller.
Since there is sufficient Mega2560 IO, the TFT01 LCD supports 16-bit mode. It is not like using 328S, only can use a set of SD card port or touch screen interface.
—3.2» LCD Screen Shiled Expansion Board—
3.2″ TFT LCD’s working voltage is 3.3V, so it can not be used directly on a standard Arduino mainboard, in order to make the TFT01 LCD compatible with standard Arduino board, this TFT Shield was designed.
Package:
1x mega2560 board
1x 3.2″ lcd display board
1x 3.2″ display board shield
1x usb cable
